In this article, you will learn how to mark or transfer pattern markings to your fabric for precision sewing!
Before we get into the nitty-gritty of marking, we need to set some ground rules…
NOTE: If you’re ready to begin this journey and would like to buy my recommended tools and supplies, please click HERE!
Marking: The Rules
Rule #2: ALWAYS test whatever method you choose on a piece of scrap project fabric — make sure it can be easily removed.
Rule #3: With the exception of pockets and buttonholes, ALWAYS make your markings on the wrong side (WS) of the fabric.
Rule #4: Whichever marking tool you choose, you want to mark as lightly as you can on the WS. NO dark, heavy marks, please.
Rule #5: Do NOT press over marks. Heat can set some dyes PERMANENTLY!
Rule #6: Never launder a garment before you remove your marks. Because some detergents may contain chemicals that make those markings PERMANENT!
Rule #7: Use PLAIN water to remove marks.
Choosing Your Marking Tools
A good marking tool has three qualities:
- It marks precisely!
- It is easily removed!
- It does not leave marks of any kind behind!
You will probably need two marking tools: one for exterior markings and one for internal markings.
Once you’ve chosen your preferred marking tools, it is time to get busy marking…
What to Mark
You’ll need to mark both layers of your fabric.
Here’s a list of everything you need to transfer from the tissue pattern pieces to your fabric:
- Button & buttonholes
- Dart point
- Pocket placement
- Positioning lines for trim or decorative stitching
- Stitching lines for curves and corners
- Start and end of gathered or eased areas
- Wrong side (WS)
- Center back (CB) at neckline and hem if not marked by a seam
- Center front (CF) at neckline and hem if not marked by a seam
- Dart legs
- Notches (these are really important!)
Okay, now that you know what to mark, you’re ready to learn the how…
How to Mark Fabric
Pin marking is easy as 1-2-3…
For example, to mark internal dart point, pocket placement, button placement, or dots…
- Place a pin in the tissue pattern at the dot or circle.
- Now, peel back the tissue paper until you get to the pin(s).
- And then mark the point where the pin pierces the fabric with a chalk pencil or a water-soluble pen, whichever is appropriate.
And since this is a dart, you’ll need to lift the fabric to reveal the other side and mark it too. Like this…
And if you laid out your fabric with wrong sides together (WST), you can easily mark both sides in one go!
Marking with Chalk or Chalk Pencil or Water-Soluble Pen
For example, here’s how you would mark a triple notch at center back (CB)…
And for darts, you can draw a line from the dart point for each dart leg. Like this…
And you’re done!
Snip marking is super easy too!
For example, if it is a notch, clip just shy of the center of the notch!
For a single notch, clip once. For a double notch, clip each notch. And for a triple notch, well, you get the idea.
And if it is the dart legs, just snip in from the cutting line. See the image above.
DO make sure that you snips are shallow — no more than ¼ inch deep! It is important not to snip too deeply as this will weaken the seam!
Isn’t snip marking too easy?!
Sew easy tip: Snip marking is only recommended for seam allowances of at least 5/8 inch!
And as you now know, you have choices and transferring pattern markings is as simple as 1-2-3.
Okay, it is time for us to get ready to get busy sewing. Because we have a lot of dreams to catch up on!
So I’ll see you over at our sewing machines.
Life is the ultimate red carpet event. Dress for it!
RELATED: Click HERE if you’re ready to unleash your dressmaking superpowers and learn how to sew a simple dress! Warning: This is a MEGA 5-part series!